Enticer

410 Yamaha Enticer with reverse. Works perfect.

Looking to buy a track for a 81 250 Enticer

Looking for a Yamaha Enticer 250. Email or send private Facebook message with what's available.

Enticer 250 parts. Motors(no carbs, not stuck, not sure if they run), gas tank, chain boxes, steering linkage, sprockets, bumpers.

Looking for 340 Enticer parts between the years 78-83 msg me with what you have

Looking for a carburetor for a enticer 2.

Looking for excellent quality parts - snow flap, hand grips and plastic bumper end caps for a 1993-2001 Yamaha Enticer 2 410 snowmobile. Willing to pay the shipping to Ontario or pickup in Corner Brook this summer.

Looking to buy a rear axel for a 1994 enticer 2. Looking for the one the 2 rear boogies bolt onto. Also interested in other enticer 2 parts.

I’m sell to skidoo they both come together the enticer work just needs a coil so done the jag there both 349 resin for sell I’m trying to get a dirtbike

Needs nothing has electric start , reverse, new seat cover and also comes with ski skins

I am selling a good Yamaha 400 motor works fine.

For parts or repair, may need top end replaced not sure, was running fine and then seized. Sled is in good shape otherwise. Please text me as my phone cant accept calls due to poor service, I will get back to you asap.

Looking to buy a track for a 1984 yamaha et300

Enticer ET340 complete suspension. $120.00

Parts for 340 Yamaha enticer .340 motor slide suspension clutch and more take all for$100

Looking to buy a 136x15 track, with a 2.52 pitch to fit my enticer 2, email with what you have thanks.

This is some stuff I have here from past machines I’ve owned. There’s individual prices or buy it all for $150. About $3-400 worth in parts, just want it gone. I have a the hand and thumb warmer switch assembly off a 700 triple bombardier, selling for $80. I also have a computer from a 99 600 mxz also asking $150, try to find one for less! Every used parts place that sell these r $200 plus, A set of Mikuni carbs 40mm with cables from a 91 Mach 1 617 but will fit others I'm sure, Carbs have pieces missing so now i am selling them for $50. carb boots off a 583 I believe $10 and the air intake tubes as well$40, I also have a carb for a 340 enticer with both boots for $60, A airbox off a ovation or Enticer 2 with no boot for $25, a coil from the same machines for $20 with no caps and a power pack for a Ovation has well for $40. Theres a few pics i dont have on here so if u need a pic text me and i will send u one of what u need. Im willing to trade all parts for a passenger quad seat, thanks for looking. text 571-1792 for quicker response, all prices are very negotiable lol take it all for $150.

I’m looking for a 144” rev chassis for a build not looking for an entire sled just a bare chassis, depending on what you have I might. message me with what you have or text 7097281600

New Sea Husky Fiberglass Boats. Offered in 28.5'. Exact Dimensions: 28.5’ Length, 9ft width maintains its beam from bow to break to stern Fabricated in house The 28.5’hull allows the entire length of the boat to be utilized. as work, rest or play space. The generous 9 ft width maintains its beam from bow break to stern, providing the length and width for a generous bow cabin and wheelhouse, if desired, or in an open boat design, to carry extra gear and fish that amazes others, for the boat size. The boat has dual chine stabilizer keels that are parallel for both extra stability and directional course maintenance (patented). Air enters the bow chine area and follows along the bottom, raising the hull or lessening the wetted surface, thus offering fuel savings by up to 20%. So whether you are cruising the canals, lakes and rivers or fishing daily out on the Atlantic, the Sea Husky is the perfect all-rounder for every use. Contact us at 700-0432 for more information.